If you do not see a flash through the camera viewfinder when a button is pressed, the remote is not sending any signal*. If you do see a flash but the remote is not working, try the other troubleshooting suggestions to help determine if the issue is the remote or something else.

If the remote does not control your system, see Remote is intermittent or does not control your Bose product.

If you do not see a flash through the camera viewfinder when a button is pressed, the console or emitter is not sending any signal*. If you do see a flash but the remote is not working, try some other troubleshooting suggestions to help determine if the issue is the remote, console, emitters, or something else. (*Some smartphone cameras have IR filters. So, if you don't see a flash, it is worth trying both the front and rear camera or a different camera to confirm.) A remote control from another product will have different or no functionality. If your have more than one Bose remote control, refer to the owner's guide of the product you are trying to control to be sure you using the right remote control.

December 1, 2022 - If your Bose remote has a screen and still doesn’t work after changing the batteries, check and see if your screen lights up when pressing the source button. If the screen lights up, most likely the remote needs to be reprogrammed. If the screen does not light, the remote is likely defective.

It seems that the issue with your ... unit is on. Here are some troubleshooting steps: Unplug the Bose Solo unit for a minute, then plug it back in and try using the remote....

Remote unresponsive despite battery replacement; infrared signal issues causing control failures. If the Bose 900 remote doesn’t power on, first verify battery orientation and use fresh batteries. Clean battery contacts to ensure good connection.

Loading · ×Sorry to interrupt · Refresh

October 25, 2022 - Next, the remote is not within the range. There is interference from other electronic devices nearby. Your Bose Soundbar or Speakers needs to be reset or updated. The remote is defective and needs to be replaced. ... So if you’re experiencing any of the issues listed above, don’t worry. Read on for a few simple solutions that might work in your case.

I cannot get it to work. I found out that my MACOS Bit Sur will not sync with my · I have a new Bose Soundbar 700, Base Module 700 and Surround Sound Speakers. I have downloaded the Bose Music app. I ... Disclaimer: The customer and expert messages presented herein may have been altered or modified to enhance readability and safeguard the privacy of individuals. These modifications do not change the intent or substance of the original messages. ... Remote unresponsive despite new batteries; pairing failures between remote and speaker unit.

(Note: For EU variants, wait 3 minutes) Replace the batteries by matching the polarity markings inside the battery compartment · For more info, see Checking the software or firmware version and Updating the software or firmware of your product. You can control your product with the SoundTouch app or the included remote control. If the app works but not the remote, the issue is related to the remote.

In case the battery or batteries in your remote are low or have no power, replace them. Alkaline batteries are recommended over rechargeable batteries, which might output lower voltage.

Loading · ×Sorry to interrupt · Refresh

October 5, 2022 - The possible reasons why the Bose remote isn’t working properly may involve the power sources, signal interruption, software issues, and hardware issues: Weak batteries or electrical interference from other devices · Weak or obstructed signal ...

If your remote is okay, it could be the IR receiver on your Bose Wave radio. Commands from the IR remote are received and detected by transistor Q802 and are fed to U301 pin 41 To verify all of that etc. we would need to see your Bose. Use these guides Bose Wave Radio AWR1-1W to work on it.

Third, select the Bose sound bar and then exit out. Your Apple TV remote should now control the Bose sound bar. ... How do I pair my Bose sound bar to work with an Apple TV remote First, on the Bose remote, hold down the Bluetooth button until you see a blue blinking light on the sound bar.

Loading · ×Sorry to interrupt · Refresh

For some reason, there is a glitch or incompatibility between this model of sound bar and maybe others and the Apple TV, where the Apple TV cannot see the signal from the Bose remote directly. The workaround is to go out and buy a cheap universal remote control.