Note: Some instructions are time-sensitive, please read the following instructions before attempting to pair. Step 1: Unplug the base power cord from your power outlet. Wait 1 minute, then plug the power cord back into your power outlet.

Perform Step 2 within 10 seconds. ... Press and hold the PAIR button on the back of the remote.

Wait 1 minute, then plug the power cord back into your power outlet. Perform Step 4 within 10 seconds, while the control box is flashing. For Second Generation Ease: Locate the Battery Backup Box and press the POWER DOWN button twice.

Open the battery cover by sliding off the back panel downward towards the bottom of the remote. Install three (3) AAA-sized batteries into the remote, matching polarity. Locate the Battery backup box under the bed and press the button TWICE. (Light will illuminate) Remove the cover from the ...

Note: Some instructions are time-sensitive, please read the following instructions before attempting to pair. Step 1: Unplug the base power cord from your power outlet. Wait 1 minute, then plug the power cord back into your power outlet.

Remote Control arrives paired to the adjustable base.

Pair Your Remote with Your Adjustable Base · Instructions for the following base models: Ease 1.0 | 2.0 · Ergo 1.0 | Ergo Power Base | Ergo Smart Base · Ergo Extend 1.0 | Ergo Extend Smart Base · Step 1 · Locate the Battery Backup Box and press the button TWICE.

Pairing the Remote with Your Base: Read Instructions · User Manuals: Ease 2.0 | Ease 3.0 · Unlocking Your Base: Read Instructions · Pairing the Remote with Your Base: Ease 2.0 | Ease 3.0 · Note: If the videos and instructions listed above are not helping you unlock your Ease, Ergo or Extend base, please click here ·

When the backlight goes away the remote is no longer in Child Lock. The remote and adjustable base will work normally. see less Hold down both buttons on the right side ( the foot raise and lower buttons ) for about 5-7 seconds it should flash a few times then it should be released.

Perform Step 2 within 10 seconds. ... Press and hold the PAIR button on the back of the remote.

Step 2: On the back of the remote press and hold the PAIR button. The PAIR button will illuminate blue and start flashing. When the PAIR button stops flashing, the LED light on the control box will go out.

This is a replacement remote compatible ... Ease 2.0 Adjustable Bases. The original black remote was discontinued and replaced by this grey serta remote (made by the original manufacture for tempur) which is easier to use and scratches less. This grey one pictured the one you will receive. We provide pairing ...

January 21, 2024 - Instructions for Ease 3.0 models: Remove the rear cover of the remote control by sliding it down to expose the PAIR button. Unplug the Power Cord from your power outlet. Press and hold the PAIR button on the back of the remote. The PAIR button ...

Step 2: On the back of the remote press and hold the PAIR button. The PAIR button will illuminate blue and start flashing. When the PAIR button stops flashing, the LED light on the control box will go out.

May 21, 2023 - Remove rear cover of the remote control by sliding it down to expose the PAIR button. Unplug the Power Cord from your power outlet. Wait 1 minute, then plug it back in to your power outlet.

Replacement Tempur-Ergo Ease Wireless Remote Control *PLEASE NOTE: Wireless remote is designed for the Tempur-Ergo Ease 2.0, 3.0 & 4.0 bases only. This will not work with other bases. Click here to identify these specific bases' remotes. If your remote does NOT look this, this replacement remote ...

Amazon.com: DHH Conversion Kit for Discontinued Leggett and Platt Prodigy 1st Gen Lost or Broken Remote : Home & Kitchen

Part/Model Number: JLDK.30.03.24 / RF399A EASE 2.0 3.0 4.0 ... Want my money back!!! ... Remote worked great. Paired immediately with my bed.