December 17, 2024 - The SharkBite deburring tool is used for measurements in the field. SharkBite Insertion Depth Chart identifies the depth needed to make a secure connection with push-to-connect fittings.

February 24, 2022 - However, they simply do not allow the pipe to be inserted the full 15/16ths of an inch that the chart specifies for a 1/2" copper pipe or PEX. I don't have the Sharkbite deburring tool that can also be used to mark the insertion depth, but it should match the 15/16ths inch spec.

SHARKBITE BRASS PUSH DEPTH GAUGE AND DEBURRING TOOL: SharkBite depth gauge and pipe deburring tool is ideal for deburring the outside of a copper pipe to remove any sharp sections or burrs; marks the proper insertion depth for SharkBite plumbing ...

July 13, 2024 - Shark Bite Depth Chart Web we tried 10 1/2 sharkbite fittings..

November 13, 2025 - Check out the insertion depth chart for the appropriate measurements. *You’ll still need a tube liner when you use SharkBite Max with HDPE SDR-9 pipe, but that should be provided by the tubing manufacturer. ... Yes. While all SharkBite brass fittings are designed for long-term use, they can be disconnected using a disconnect clip, tongs, or the pro disconnect tool if necessary. Is the warranty the same for Max and 1st ...

SharkBite® depth gauge; Deburring and depth gauge all-in-one; Gauge measures proper installation depth; For 1/2", 3/4" and 1" PEX, copper and CPVC pipe; Prices shown do not include taxes. While every effort is made to maintain prices shown, we reserve the right to adjust prices when necessary ...

June 1, 2014 - There are sharkbites for copper/cpvc and a different one for the grey quest pipe. ... The 1" depth mark is only to allow a fitting to be removed when in close proximity to another fitting or joint...it's not the seating depth.

For full functionality of this site it is necessary to enable JavaScript. Here are the instructions how to enable JavaScript in your web browser

SharkBite · stallation Guide · bite.com · he Total · umbing Solution · Done · pe square · rough edges and · ark the pipe to the · sertion depth

This durable deburring tool allows you to deburr the outside of a copper pipe to remove any sharp sections or burrs and mark the proper insertion depth for SharkBite Max and First generation fittings.

April 4, 2022 - It's in the measurements: O.D. vs I.D. 1/2" ID will (in most wall thicknesses) translate to 5/8" OD. HVAC speaks in O.D. and Plumbing speaks in I.D. A 1/2" Plumbing fitting should slip into/onto a copper pipe with 5/8" O.D. measurement.

No,it will fit 1/2 inch copper tubing,if you google it might tell you what size sharkbite will fit a 5/8

REDIGRIP FITTING SIZE Normal Pipe Size · PIPE INSERTION AND DEPTH CHART

August 14, 2025 - Check the SharkBite insertion depth chart* for the correct depth for your application.

We cannot provide a description for this page right now

August 12, 2025 - Pipe insertion depths for SharkBite fittings vary depending on the size of the fitting. Up-to-date pipe insertion depths can be found in the insertion depth chart.

Depth MM · 1/2 in. 1/2 in. CTS · 5/8 in. 1 in. 25 · 3/4 in. 3/4 in. CTS · 7/8 in. 1-1/4 in. 32 · 1 · 2 · The SharkBite connection system is certified for potable water and radiant heating. SharkBite uses an advanced push-to-connect design that works in two stages.

2. Deburr the end of the pipe using the SharkBite F702 Deburring tool. Be sure to remove any sharp edges that · may damage the O-Ring, as this will cause failure. 3. Mark the pipe with a marker, using the SharkBite F702 Gauge to determine the correct insertion depth...