I am having the exact same problem since I upgraded to Windows 11 24H2.
PLEASE DO NOT DO THIS: I thought I will uninstall frescologic driver and reinstall it to fix the issue. But after reinstalling the driver, I am unable to get the second monitor(frescologic USB to VGA/HDMI) working at all.
I tried DDU (Display Driver Uninstaller) but it still does not work..
Edit: Finally after a lot of hit and trial, I was able to get the second monitor working. I am not sure which steps were relevant but below is what I did:
- from Device Manager -> Display Adapters, Right click the "fresco logic iddcx adapter" -> Uninstall Device -> Check the attempt to remove driver.
- from Device Manager -> USB Video class device , Right click the "fresco logic FL2000 USB Display Adapter" -> Uninstall Device -> Check the attempt to remove driver.
- By launching the installer, I uninstalled the newer frescologic driver I had already installed (FL2000-2.1.36287.0.exe)
- Restart
- Install the driver version which came in with the device "Windows install_2.1.34054.0" - Windows install_2.1.34054.0.exe
Freco Logic Usb3 to VGA issue
Problem with Fresco Logic IDDCX Adapter (hdmi to usb) Screen Flashing black
USB driver update recommended for Fresco Logic expansion card
You can get the Fresco Logic drivers here:
https://support.zoho.com/portal/frescologic/home (USB 3.0 Host Driver (FL1000, FL1009, FL1100) v3.6.8.0)
But beware, I have had the best experience with the windows 10 drivers. I got two scenarios:
-
Installed an older fresco logic driver from the Inateck website -> Got bluescreens after reboot
-
Installed the latest driver from fresco logic website (the one from the link) -> Worked flawlessly at first, but made my rift shut off for a few seconds now and then.
Went back to windows 10 drivers: Everything worked again as expected.
More on reddit.comFresco Logic 3.0 USB
I am having the exact same problem since I upgraded to Windows 11 24H2.
PLEASE DO NOT DO THIS: I thought I will uninstall frescologic driver and reinstall it to fix the issue. But after reinstalling the driver, I am unable to get the second monitor(frescologic USB to VGA/HDMI) working at all.
I tried DDU (Display Driver Uninstaller) but it still does not work..
Edit: Finally after a lot of hit and trial, I was able to get the second monitor working. I am not sure which steps were relevant but below is what I did:
- from Device Manager -> Display Adapters, Right click the "fresco logic iddcx adapter" -> Uninstall Device -> Check the attempt to remove driver.
- from Device Manager -> USB Video class device , Right click the "fresco logic FL2000 USB Display Adapter" -> Uninstall Device -> Check the attempt to remove driver.
- By launching the installer, I uninstalled the newer frescologic driver I had already installed (FL2000-2.1.36287.0.exe)
- Restart
- Install the driver version which came in with the device "Windows install_2.1.34054.0" - Windows install_2.1.34054.0.exe
Hello KOSTAS RODIS and welcome to the Microsoft Community!
According to your feedback, you are experiencing an update to Windows 11 24h2 and the monitor has to be disconnected and reconnected for it to display!
You can uninstall the driver for your monitor by clicking on the windows key > search and open Device Manager > uninstall the driver for your monitor.
Then you can go to the official website of your motherboard and download the chipset driver of your motherboard again.
At the same time, update your computer's graphics card driver
Then restart your computer and connect your monitor to see if the problem persists.
If this does not solve your problem
You can also try to uninstall the update by clicking on windows key > settings > windows update > update history.
Uninstall the update and see if the problem persists after uninstalling it.
This will help you to rule out if the problem is caused by the update.
I hope you find the above information helpful.
Kirito|Microsoft Community Support Specialist
Hi Nicolaslafo,
I'm Rodrigo and I will help you.
The adapter needs to be connected to a USB 3.0 port to work correctly, if it is connected to a USB 2.0 port it will work on a maximum resolution of 800x600.
If it is already connected to a USB 3.0 port, try another available port
With a little research, I found that it is a common issue with this adapter, here is a possible fix that I've found:
Go to the Fresco Logic driver installation folder (default path: C:\Program Files\Fresco Logic\Fresco Logic USB Display Driver\FL2000\x64) and open fresco_monitor_tool.exe . Set the resolution and refresh rate but slowly increase from 800x600 until you find a suitable working resolution. Set the refresh rate to 60HZ, and if needed, reduce it. Select Set EDID to apply the changes, Clear EDID will clear the changes you did.
I purchased the Oculus recommended Fresco Logic USB expansion card and installed it into my PC. It's not supposed to require any external drivers with the included Windows 10 drivers being sufficient. Oculus Home however is complaining with "USB driver update recommended".
I've searched and cannot find any drivers to update to. Is anybody else getting this warning?
You can get the Fresco Logic drivers here:
https://support.zoho.com/portal/frescologic/home (USB 3.0 Host Driver (FL1000, FL1009, FL1100) v3.6.8.0)
But beware, I have had the best experience with the windows 10 drivers. I got two scenarios:
-
Installed an older fresco logic driver from the Inateck website -> Got bluescreens after reboot
-
Installed the latest driver from fresco logic website (the one from the link) -> Worked flawlessly at first, but made my rift shut off for a few seconds now and then.
Went back to windows 10 drivers: Everything worked again as expected.
Don't do it. The new drivers didn't work right with my CV1 and I had to roll them back.
Hi RenéBravo
Greetings! I am Vijay, an Independent Advisor. I am here to work with you on this problem.
What is the exact issue which you get? Any screenshot?
Hi Rene,
If the driver from the cards installation disc (if the card is/was an add-on) or if the driver from the Fresco site was downloaded and installed, completely uninstall all of those (these drivers are basically for Win 7/Vista/XP support) then restart the PC and let Windows update install the driver(s) that it likes.
The add-on cards (in my case an Inatech 7 Ports PCI-E to USB 3.0 Expansion Card installed in Feb. 2016) that use the Fresco Logic (FL1100) chipset were always plug-n-play with Windows 10 with the best results. (Those that mistakenly installed the old drivers had problems).
Or, if you are referring to (using) the FL2000 USB 3.0 Display device controller then also refer to the links below:
https://support.frescologic.com/portal/home
https://support.frescologic.com/portal/kb/articles/fl2000-recommended-usb-3-0-xhci-host
https://support.frescologic.com/portal/kb/fresco-logic/faq/vga
Hope this helps,
-Richard