No. Ethernet ports can't transmit or receive RS-232 signals.
If your laptop has a traditional DB9 RS-232 serial port, use that with the appropriate serial cable. If it doesn't, use a USB to RS-232 serial adapter.
Answer from Spiff on Stack ExchangeNo. Ethernet ports can't transmit or receive RS-232 signals.
If your laptop has a traditional DB9 RS-232 serial port, use that with the appropriate serial cable. If it doesn't, use a USB to RS-232 serial adapter.
If you have something like this item, then it is merely a pinout adapter and not a serial/ethernet device.
You could use one of these on each end of a RJ45 cable to make a serial cable. That serial cable could run through structured cable installed inside a wall or similar, but it cannot run through an ethernet switch or vlan.
Can I put RJ45 connectors on RS232 9-pin cable?
cables - Pin assignment on rj45 when using rs232 - Electrical Engineering Stack Exchange
Serial Console over RJ45 Ethernet-Patchpanels / RS232-Ethernet-Pinout?
Is there any way to connect a RS232 device with an RJ25 port to another RS232 device with an RJ45 port?
Videos
Those plugs are most likely (hard to tell from a picture) Cisco console cable plugs.
They convert a DB-9 serial interface to a RJ45 receptacle , but NOT for use with a regular network cable. (They also exist in a DB-25 version.)
They are intended to use with a Cisco console cable (that has a RJ45 plug on 1 end and a DB-9 on the other) or a roll-over cable (RJ45 plug on both ends, but different pin-out than a network cable).
A Cisco console cable + a plug like yours connected to the other end make together a serial 3-wire null-modem cable.
A roll-over cable with 2 of these plugs (on each end) also makes a 3-wire null-modem cable.
That may be all you need. Provided that your lab-device needs a 3-wire null-modem cable, which is the most common case.
But some require a straight cable and in some (rare) cases you need a 5-wire null-modem (or straight) cable.
As modern computers, especially laptops, typically don't have a DB-9 serial port anymore, you may also need a USB to serial converter plug.
For short: There are a lot of variables here. Without more details about the devices involved and the exact nature of your plugs I can't get any more specific.
As Tonny wrote, that adapter is most likely a Cisco RJ45-to-DB9 converter, which is a purely passive adapter. The RJ45 side is not Ethernet, it's just RS232 on a different type of connector (Cisco devices used to have console ports with an RJ45 connector rather than the more common DB9 or DB25 connectors).
If you have an RS232 port on your laptop, then you just need a cable. While this was extremely common a couple of decades ago, nowadays I believe it's quite rare to find a laptop with an RS232 port.
So what you need instead is more likely an RS232-to-USB (aka serial-to-USB) converter/adapter.
Once you have that, you should have a new character device for the serial port somewhere in /dev (details may vary, but probably some kind of /dev/tty-something).
If you just want to capture the data from the serial port to a file, you can just cat /dev/serial_port_device_name >filename.
If you need to change serial port settings you can use stty but beware that you must keep the port open while you do it, otherwise the settings will reverse to defaults right away.
If you want something more foolproof, you can probably write a short script using the language of your choice, or they may be additional tools to manage that.
Alternatively there are devices with serial ports and Ethernet connections (you would then usually use telnet or netcat to connect to the serial ports and capture the data), but these would be more expensive, and only useful if you need to capture data from a larger distance.
I have Belden 9539 (RS232 cable, 9 pin) already run in a building. Can I put an RJ45 connector on both ends of this cable, will it work? I'd just leave out the ground pin. I don't see why it wouldn't work, even if it's not the ideal solution. Any thoughts? This is for connecting the LAN port of a PTZ camera to the PTZ controller.