December 17, 2024 - The SharkBite deburring tool is used for measurements in the field. SharkBite Insertion Depth Chart identifies the depth needed to make a secure connection with push-to-connect fittings.

February 24, 2022 - However, they simply do not allow the pipe to be inserted the full 15/16ths of an inch that the chart specifies for a 1/2" copper pipe or PEX. I don't have the Sharkbite deburring tool that can also be used to mark the insertion depth, but it should match the 15/16ths inch spec.

July 13, 2024 - Shark Bite Depth Chart Web we tried 10 1/2 sharkbite fittings..

SharkBite® depth gauge; Deburring and depth gauge all-in-one; Gauge measures proper installation depth; For 1/2", 3/4" and 1" PEX, copper and CPVC pipe; Prices shown do not include taxes. While every effort is made to maintain prices shown, we reserve the right to adjust prices when necessary ...

For full functionality of this site it is necessary to enable JavaScript. Here are the instructions how to enable JavaScript in your web browser

This durable deburring tool allows you to deburr the outside of a copper pipe to remove any sharp sections or burrs and mark the proper insertion depth for SharkBite plumbing fittings.

June 1, 2014 - There are sharkbites for copper/cpvc and a different one for the grey quest pipe. ... The 1" depth mark is only to allow a fitting to be removed when in close proximity to another fitting or joint...it's not the seating depth.

April 4, 2022 - It's in the measurements: O.D. vs I.D. 1/2" ID will (in most wall thicknesses) translate to 5/8" OD. HVAC speaks in O.D. and Plumbing speaks in I.D. A 1/2" Plumbing fitting should slip into/onto a copper pipe with 5/8" O.D. measurement.

1-1/2", and 2" The SharkBite 2XL is compatible with copper, PEX and CPVC pipe and is certified for

SharkBite · stallation Guide · bite.com · he Total · umbing Solution · Done · pe square · rough edges and · ark the pipe to the · sertion depth

November 13, 2025 - Check out the insertion depth chart for the appropriate measurements. *You’ll still need a tube liner when you use SharkBite Max with HDPE SDR-9 pipe, but that should be provided by the tubing manufacturer. ... Yes. While all SharkBite brass fittings are designed for long-term use, they can be disconnected using a disconnect clip, tongs, or the pro disconnect tool if necessary. Is the warranty the same for Max and 1st ...

SharkBite deburr & gauge tool is an all in one tool that measures insertion depth for fittings and deburrs copper pipe. View now.

REDIGRIP FITTING SIZE Normal Pipe Size · PIPE INSERTION AND DEPTH CHART

Depth MM · 1/2 in. 1/2 in. CTS · 5/8 in. 1 in. 25 · 3/4 in. 3/4 in. CTS · 7/8 in. 1-1/4 in. 32 · 1 · 2 · The SharkBite connection system is certified for potable water and radiant heating. SharkBite uses an advanced push-to-connect design that works in two stages.

May 19, 2025 - Check the SharkBite insertion depth chart* for the correct depth for your application.

August 14, 2025 - For a complete list of first-generation and SharkBite Max insertion depths, check the Insertion Depth Chart.

Check each product page for other buying options. Price and other details may vary based on product size and colour · Pipe Deburr, Depth Gage and Disconnect Tool for Push-to-Connect System, Push-fit System, Multi-Size Combination 1/4 in.-1 in · Full Size 3/8"-1" Deburring Pipe and Depth Gauge ...

2. Deburr the end of the pipe using the SharkBite F702 Deburring tool. Be sure to remove any sharp edges that · may damage the O-Ring, as this will cause failure. 3. Mark the pipe with a marker, using the SharkBite F702 Gauge to determine the correct insertion depth...